Can I Install a Bath Tub Myself? Considerations And Actions

Get Started

In this article in the next paragraph you can locate some really good expertise around Installing A Bathtub.


How to Install a Bathtub Yourself
Installing a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately challenging project. If the old tub is readily available, the job can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a house handyman's skills, although you will need a helper to leave the old tub and set in the new one. Make sure you have qualified yourself for the work and also fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and also product checklist need to make up the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Planning for the Installment


    First of all, the supporting structure provided with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
    Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
    Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.

    Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, activate the faucets to drain any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome as a result of the limited access that is frequently the case.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the remaining water that will originate from the pipelines. Once the supply pipes have been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
    Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Mounting the Tub


    Utilizing the two wooden boards under its feet, put the bathtub in the required position. The wooden boards are helpful in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
    The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bathtub until the spirit level reads degree.
    To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
    Turn on the water supply and check all joints and brand-new pipework for leakages and also tighten them if essential. Load the tub and likewise check the overflow outlet and the regular electrical outlet for leakages.
    Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been made use of at the very least when as this will settle it into its final position.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
    If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bath and the tiling, causing problems with wetness and feasible leaks to the ceiling listed below.
    You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into consideration this movement prior to securing.
    Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    As a serious person who reads about How to Install a Bathtub, I figured sharing that article post was really useful. Enjoyed our blog entry? Please share it. Let others locate it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.




    Schedule Appointment


    Leave a Reply

    Your email address will not be published. Required fields are marked *